|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
14-09-2010, 01:25 AM
|
#1 | ||
|
Starter Motor
Join Date: Aug 2010
Posts: 15
|
Hey fellas, does anybody know if the WS Fez front seats are a straight fit into a WQ. The WQ seats are just too flat and unsupportive. XR4 ones are rare as well.
Say I got seats from any other car, say a WRX for the argument. Would someone be able to fit them. Who would do that, and at what cost? I was reading elsewhere for it to be fully legal you need an engineer to look over it as well. Understandable I guess. Thanks. |
||
|
|
|
14-09-2010, 07:10 AM
|
#2 | ||
|
Finally rollin on 20's
Join Date: Sep 2005
Location: Brisbane
Posts: 1,951
|
Early WRX seats fit but you have to have rails made for them, only other option is to have the seats re-done by an upholsterer!!!
I was looking into just replacing the 'bubbles' on my seats but can't figure out how to remove the rear seat base to make the start!! Cheers
__________________
Fiesta ST..... Colorado Red...... SOLD Territory Turbo Ghia ..... Winter White SOLD - Good bye my little buddy!!!! K&N, F6 Snorkel, Debung, 20" Enix Turbine in Gunmetal, 7 seat rear springs. |
||
|
|
|
|
14-09-2010, 09:37 AM
|
#3 | ||
|
Deaf Driver
Join Date: Aug 2009
Location: Canberra, ACT
Posts: 276
|
These WS seats have Airbags inside, would it be an hassle to have them re-wired or something?
__________________
Former owner of 2009 5dr Silverdust Ford Fiesta Zetec (Manual) In the look out for WS/WT Zetec Ford Fiesta (Manual only) in 2016. |
||
|
|
|
|
14-09-2010, 10:48 AM
|
#4 | ||
|
Finally rollin on 20's
Join Date: Sep 2005
Location: Brisbane
Posts: 1,951
|
I don't think the CL does, but there should be a connector under the seat for side airbags from memory (Ford used a generic wiring loom for WQ)
__________________
Fiesta ST..... Colorado Red...... SOLD Territory Turbo Ghia ..... Winter White SOLD - Good bye my little buddy!!!! K&N, F6 Snorkel, Debung, 20" Enix Turbine in Gunmetal, 7 seat rear springs. |
||
|
|
|
|
14-09-2010, 05:16 PM
|
#5 | ||
|
Starter Motor
Join Date: Aug 2010
Posts: 15
|
Upholsterer. I wonder if they could build more of a wing on the bottom bit, there's not much seat to work with. I'll have to go to an upholsterer to see how much they would charge to make a rail to fit another seat. Around 200 would be OK.
|
||
|
|
|
|
14-09-2010, 05:23 PM
|
#6 | ||
|
FF.Com.Au Hardcore
Join Date: Jun 2009
Posts: 612
|
Upholsterers can add foam and the like to make the seat more to your liking.
Its probably easier than sourcing new seats and then getting new brackets made up too... |
||
|
|
|
|
14-09-2010, 05:31 PM
|
#7 | ||
|
Starter Motor
Join Date: Aug 2010
Posts: 15
|
Maybe I should lose some weight, be cheaper. Haha.
|
||
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
Seats, WS into WQ
Linear Mode
